Precision High Speed Stator Punching Machine

Model: MDH-65T
Brand: OREKU KOJO PRECISION MACHINE
Precision: JIS special grade
Speed: 700 times/min
Tonnage: 65 tons
Stroke: 30mm
Price: Negotiable.

 Standard accessories for precision high speed stator punch press:
1. Motorized die height adjustment
2. Die height display accuracy 0.01
3. Inching function Single function Linkage function
4. Linkage with 0° and 90° positioning and stopping function
5. Slider pad
6. Six groups of batch control
7.Two groups of slanting groove control
8.Hydraulic mold clamping
9. Hydraulic seat screw pile
10.Hydraulic mold lifter and lifting arm
11.Lubricated cooling circulator
12.Independent electric control box
13.Positive and negative reversing device of main machine
14.Separate brake clutch
15.Spring type anti-vibration feet
16.Working light
17.Maintenance tools and tool box
Precision high speed stator punch press optional accessories:
1.Gear feeder (width selection: 150/200/300/400)
2.NC servo feeder
3.Double-head material holder (hydraulic expansion/manual expansion) (width selection: 200/300/400)
4.S-type leveling machine
5.Tonnage detector
6.Lower dead center monitor
7.Electric control box air conditioner
8.Frequency conversion permanent magnet motor
Precision High Speed Stator Punching Machine Technical Parameters:
Nominal force: 65T
Capacity generating point: 2.0mm
Stroke: 30mm
Stroke number: 150-700s.p.m
Working table area: 950×650 mm
Unloading hole：700×125mm
Slide area：950×420mm
Stroke of die height adjustment：300-350 mm
Mold height adjustment motor: 0.4kw
Motor of main machine：19kw
Outer size：2010×1660×2950 mm
Total weight: 12.5 tons
Structure of Precision High Speed Stator Punching Machine

Precision High Speed Stator Press Stamping Products

Precision high-speed stator punch press maintenance:

 1, often keep the center column, the slider guide column clean, as well as racking the mold to keep the mold base plate free of dirt to ensure the cleanliness of the platform to avoid scratches. 2, the new machine in the use of 1 month, the flywheel at the addition of grease (including feeder), if the long time no refueling, will lead to internal wear and tear of the flywheel, affecting the performance of the machine tool, and then every time the maintenance needs to be added (high temperature 150 ℃ more than the grease) 
3, the replacement of machine circulating oil: new machine in 1 month to replace 1 time, and then every six months to replace 1 time, to ensure the normal operation and precision of the machine tool (32 # mechanical oil or Mobil 1405 #)
Precision high-speed stator punch press use method:
1, before starting the machine, the speed potentiometer (W) set on the control panel should be adjusted to the lowest point (O point) position.
2、After the main power switch (DK) is turned on, the power indicator light is on, and the phase sequence indicator light should also be on, otherwise the phase sequence should be checked to see if it is correct.
3、Break the phase after turning on the control circuit with the key switch. Indicator lamp three should be bright at the same time, otherwise should check, troubleshooting.
4, clockwise adjustment of the “speed” potentiometer, the main motor drive flywheel start, the speed should be smooth without vibration, no impact and other phenomena exist.
5, in the process of connecting the main clutch, should be operated at the same time left and right hand. In the process of formal stamping, the external control key switch should be turned on and the key switch of the regulator should be in the state of reset before it can work formally, otherwise the feeding switch and the mold failure signal will be out of control.
6、During the formal stamping process, since the static differential rate of the main motor varies with different loads, when stamping different parts, the electromagnetic register set on the control board can be used to correct the rotational speed.